← Back to the full lesson

Intercepting and tracking VOR courses: summary

Full lesson and practice: pilotscafe.com/intercept-and-track-vor/

Tune and identify

  • Identify by the Morse code, or a recorded voice that says the name followed by "VOR". Not by a flight service station's or approach control's voice.
  • If the receiver decodes and displays the identifier, you don't need to listen. A database identifier alone is not a decode.
  • T-E-S-T or no identifier: maintenance. A missing identifier means officially off the air, possibly unreliable.
  • Don't fly a procedure NOTAMed out of service, even if the identifier transmits.
  • IFR use: a VOR check within the preceding 30 days, found within limits, or an approved maintenance procedure (14 CFR 91.171).

The VOR indicator

  • Omnibearing selector (OBS): sets the course under the index.
  • Course deviation indicator (CDI): centers on the selected radial or its reciprocal. Edge of the center circle 2°, each dot 2° more; full deflection 12° or more (normal sensitivity).
  • TO/FROM: where the selected course leads if intercepted and flown. Not where the nose points.
  • Flag: OFF, a blank or OFF in the TO/FROM window means an unreliable signal.
  • Set the OBS to the course you intend to fly: TO flying to the station, FROM flying away. The reciprocal gives reverse sensing; you would turn away from the needle.
  • Horizontal situation indicator (HSI): the deviation bar shows the course as if looking down on the airplane. TO triangle points toward the head of the course pointer, FROM toward the tail.

Station passage

  • Rapid or fluctuating needle movement: the station is near. Avoid overcontrolling.
  • Over the station: zone of confusion, needle swings.
  • Positive passage: TO changes to FROM. Passing to one side, the needle deflects toward the station.
  • Don't use a reading taken while transmitting on the NAV/COM.
  • Outbound on the same course: leave the OBS. New radial: set it and intercept.

Intercept (IFH method)

  1. Orient: center the needle. With FROM, the index shows your radial.
  2. Difference between the radial to intercept and your radial.
  3. Double it: the intercept angle, no less than 20°, no more than 90°.
  4. Set the OBS to the desired radial, or the inbound course.
  5. Turn to the intercept heading: course − angle with the needle left, + with it right.
  6. Keep it until the needle centers, leading the turn. Then track.

Example: 300 TO = 120 radial. Cleared to the 170 radial inbound: course 350°. (170 − 120) × 2 = 100°, capped at 90°. Needle left; heading 350° − 90° = 260°, then a right turn onto 350°.

Bracket the wind

  • Heading = course, needle moving left: crosswind from the left.
  • Turn 20° toward the needle. When it recenters, halve the correction.
  • Needle moving the other way: too much. Return to the course, then fly a smaller correction.
  • Wait a moment before reacting to small needle movements. Chasing the needle is homing, not tracking.

Example: 350 → 330 → 340 → (too much) 350 → 345. WCA 5° left.

Service volumes (AIM 1-1-8)

ClassAltitude (ft ATH)NM
T1,000–12,00025
L1,000–18,00040
H1,000–14,500 / 14,500–60,000 / 18,000–45,00040 / 100 / 130
VL1,000–<5,000 / 5,000–<18,00040 / 70
VH1,000–<5,000 / 5,000–<14,500 / 14,500 up40 / 70 / as H

Accuracy generally ±1°; propeller RPM can swing the CDI ±6°. VOR MON: coverage at 5,000 ft AGL outside the Western U.S. Mountainous Area; a MON airport within 100 NM in the contiguous U.S.

ACS V.A

Headings ±5°, altitude ±100 ft, airspeed ±10 kt, CDI within ¾ scale. Recognize a facility or system failure and report it to ATC when required.